Many homeowners love shower surrounds made of fiberglass compared to custom tile designs. It is not just usually cheaper and less expensive, but it also can lower the maintenance you must perform on the walls of your shower. Additionally, they’re generally simpler to put in. We will help you understand the following question in this blog post.
Yes, you can have frameless shower doors installed on fiberglass showers. Many homeowners wonder if it’s feasible to put shower doors in an aluminum surround. There’s a good point that it’s generally possible. Be aware that you aren’t able to install frameless shower doors in an acrylic or fiberglass showers opening that does not have wood blockage behind it, as thin plastic materials won’t offer enough support to the door and will not support the screws.
You should notice a few things before you begin installing your shower door. The planning process will not only aid you in overcoming any challenges but also help ensure that the installation goes smoothly. Here is a complete guide for you. Let’s begin.
The Frameless Shower Door Installation Procedure
Here is the main procedure for installing a frameless shower door.
- Clean up the entire area. It includes all the wall surfaces you’ll put in the enclosure and the floor. Check whether the glass door is suitable.
- Then, secure the hinges and handle to the pane of glass. Be careful not to secure the hinges too tightly to avoid lousy breakage or damage to the glass.
- The shorter panel is the door that swings and places on top. This panel is equipped with an aerator to stop leaks. The water sweep is the rubber or plastic strip affixed onto the lower part of the door swinging. After that, you can place the wood shims onto the floor.
- Then, take the larger panel to the door that swings. The gap between the two panels, from the bottom to the top, is 1/16 inches. Also, you must ensure that both glass panels are in a level position.
- Mark with a pencil the holes through which the hinges will be attached. Make the holes you’ve marked, and then attach the anchors. If you find that anchors’ heads do not even, you can cut them off using an edger.
- Then, grab your shorter glass panel (the doors that swing) and set them on the wood shims. Set everything up in a straight line and be aware of the gap of 1/16 inch. Now, you can secure the hinges onto the wall in the correct order.
- Then, add the water sweep at the bottom of the hinged doors (that is, the smaller panel).
Specific essential steps to be taken:
Here are some steps that needs to follow:
Step 1
Measure the bottom of your shower doorway to calculate the length of the bottom track of the shower door. Wear your protective glasses and use the hacksaw to cut the way to fit the proper measurement.
Step 2
Install the door track at the center of the bottom frame for the shower. Be sure that the track’s higher side faces the side from the shower. By doing this, water will not leak from the shower and onto the floor. Tape the track on the base of the shower with masking tape. Draw the position of the track using the pencil.
Step 3
The wall channels should be inserted into the track at the bottom of the door. The pipeline should be aligned with the edges of the frame, and mark the position of the screw holes using a pencil. Repeat these steps to install the wall channel on the shower’s opposite wall.
Step 4
Drill a hole through each pencil mark on the shower door frame to create wall channels and the door’s bottom track.
Step 5
Apply the silicone sealer to the walls’ bottom. Then press into the walls and place the wall channels into holes you’ve drilled into the shower made of fiberglass. Screw the wall channels as well as the bottom track this way.
Step 6
Find the distance between wall channels near the highest point of your shower head. Cut the shower head to be equal to the measurement. Slide the shower header over those wall channels to create the frame for the shower door.
Step 7
Connect the shower door to the frame with the hinges that come with it and the screws. Check that the sealing between the shower door is sealed to ensure that water cannot escape when you shower.
Step 8
Use any additional silicone sealer to the shower’s frame to form an airtight seal between the interior and exterior of the shower. Before you use the shower, let the sealer sit for 24 hours.
Frequently Asked Question(FAQs):
Is it possible to install frameless glass doors on an existing bathtub?
We’re pleased to announce that it is indeed true! There’s no reason showers require every frameless glass amusement. There are various positive reasons to install a frameless glass door in your bathtub. The following four reasons to surround your tub with frameless shower doors are a smart idea.
What kind of door for the shower is the easiest to wash?
Frameless doors are easy to maintain and clean compared to doors with frames. Additionally, they provide modern elegance and have an airy feeling. They also work excellently in smaller baths.
What is the cost of frameless shower doors that set you back?
If you want a custom frameless shower door (the most effective option we’ve found), You’re probably expecting to spend between $900 and $1300 for a panel and door. The median is about $1,000, and installation usually costs around $300.
Related: Can you install shower doors on porcelain tiles?
Conclusion
If a professional completes it, this task can aid you in avoiding costly problems like leaks or water damage that can happen in the future. Furthermore, they can simultaneously put up the door to your shower and walls, save you valuable time during the process, and allow you to enjoy your shower earlier. I hope this guide will help you more.